Showing results: 46 - 60 of 62 items found.
-
A10160 -
Tabor Electronics Ltd.
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
9100 -
Tabor Electronics Ltd.
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
9400 -
Tabor Electronics Ltd.
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
9200A -
Tabor Electronics Ltd.
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
9200 -
Tabor Electronics Ltd.
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
9100A -
Tabor Electronics Ltd.
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
-
310113456 -
Virginia Panel Corporation
The strain relief attaches to the wiring side of the iCon receiver and can be secured before receiver installation. The strain relief is made of aluminum and black powder coated and includes 6 wire ties.
-
Type 131 -
Datum Electronics, Ltd.
The Type Load Cell 131 Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor allowing the user to use the data from the load cell in a more efficient and productive way.The Type 131 Load Cell Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor. It can be calibrated to provide a 4-20mA output for a fixed load range from the sensor.
-
LCD20 -
Mantracourt Electronics Ltd
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
PENKO Engineering B.V.
PENKO designs and manufactures a wide range of Amplifiers - also known as digitizers and signal conditioners or PLC weighing cards - which are available as analog or digital versions. These are suitable for use with all types of strain gauge load cells and a number of configurations supplied by PENKO.
-
Datum Electronics, Ltd.
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Type 132 -
Datum Electronics, Ltd.
The Type 132 Amplifier is designed to amplify the signal from any load cell with full bridge connection, allowing the user to use the data from the load cell in a more efficient and productive way.The Type 132 Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor. It can be calibrated to provide a 0-10V output for a fixed load range from the sensor.
-
SY038 -
Synectic Electronics
The SY038 is a strain gauge bridge amplifier ideal for use in load cell amplification. This Load Cell Amplifier has a variable gain functionality using a miniature dip switch which enables the user to select one of 16 ranges for transducer outputs as low as 0.25mV/V and up to 4.4mV/V, higher if specified. It has the best stability in its class and high immunity to interference. Non-interactive Zero and Span trimmers are screw driver adjustable giving a further +/-20% adjustment.
-
Vetek Weighing AB
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.